LoRaWAN-Modbus-Gateway/libraries/ArduinoModbus/examples/TCP/WiFiModbusServerLED/WiFiModbusServerLED.ino

/*
  WiFi Modbus TCP Server LED

  This sketch creates a Modbus TCP Server with a simulated coil.
  The value of the simulated coil is set on the LED

  Circuit:
   - MKR1000 or MKR WiFi 1010 board

  created 16 July 2018
  by Sandeep Mistry
*/

#include <SPI.h>
#include <WiFiNINA.h> // for MKR WiFi 1010
// #include <WiFi101.h> // for MKR1000

#include <ArduinoRS485.h> // ArduinoModbus depends on the ArduinoRS485 library
#include <ArduinoModbus.h>

#include "arduino_secrets.h"
///////please enter your sensitive data in the Secret tab/arduino_secrets.h
char ssid[] = SECRET_SSID;        // your network SSID (name)
char pass[] = SECRET_PASS;    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;                 // your network key Index number (needed only for WEP)

const int ledPin = LED_BUILTIN;

int status = WL_IDLE_STATUS;

WiFiServer wifiServer(502);

ModbusTCPServer modbusTCPServer;

void setup() {
  //Initialize serial and wait for port to open:
  Serial.begin(9600);
  while (!Serial) {
    ; // wait for serial port to connect. Needed for native USB port only
  }

  Serial.println("Modbus TCP Server LED");

  // attempt to connect to WiFi network:
  while (status != WL_CONNECTED) {
    Serial.print("Attempting to connect to SSID: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    status = WiFi.begin(ssid, pass);

    // wait 10 seconds for connection:
    delay(10000);
  }

  // you're connected now, so print out the status:
    printWifiStatus();

  // start the server
  wifiServer.begin();

  // start the Modbus TCP server
  if (!modbusTCPServer.begin()) {
    Serial.println("Failed to start Modbus TCP Server!");
    while (1);
  }

  // configure the LED
  pinMode(ledPin, OUTPUT);
  digitalWrite(ledPin, LOW);

  // configure a single coil at address 0x00
  modbusTCPServer.configureCoils(0x00, 1);
}

void loop() {
  // listen for incoming clients
  WiFiClient client = wifiServer.available();
  
  if (client) {
    // a new client connected
    Serial.println("new client");

    // let the Modbus TCP accept the connection 
    modbusTCPServer.accept(client);

    while (client.connected()) {
      // poll for Modbus TCP requests, while client connected
      modbusTCPServer.poll();

      // update the LED
      updateLED();
    }

    Serial.println("client disconnected");
  }
}

void updateLED() {
  // read the current value of the coil
  int coilValue = modbusTCPServer.coilRead(0x00);

  if (coilValue) {
    // coil value set, turn LED on
    digitalWrite(ledPin, HIGH);
  } else {
    // coild value clear, turn LED off
    digitalWrite(ledPin, LOW);
  }
}

void printWifiStatus() {
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");
  Serial.println(WiFi.SSID());

  // print your WiFi shield's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");
  Serial.println(ip);

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.print(rssi);
  Serial.println(" dBm");
}