renamed project

cube/Core/Src/gpio.c

@@ -0,0 +1,87 @@
+/**
+  ******************************************************************************
+  * File Name          : gpio.c
+  * Description        : This file provides code for the configuration
+  *                      of all used GPIO pins.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2020 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "gpio.h"
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/*----------------------------------------------------------------------------*/
+/* Configure GPIO                                                             */
+/*----------------------------------------------------------------------------*/
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */
+
+/** Configure pins as
+        * Analog
+        * Input
+        * Output
+        * EVENT_OUT
+        * EXTI
+*/
+void MX_GPIO_Init(void)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+
+  /* GPIO Ports Clock Enable */
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(GPIOC, LED_Heartbeat_Pin|LED_Error_Pin|LED_Operation_Pin, GPIO_PIN_RESET);
+
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(GPIOD, Frontend_Out_Pin|Loop_Disable_Pin|Loop_Enable_Pin, GPIO_PIN_RESET);
+
+  /*Configure GPIO pins : PCPin PCPin PCPin */
+  GPIO_InitStruct.Pin = LED_Heartbeat_Pin|LED_Error_Pin|LED_Operation_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+  /*Configure GPIO pins : PDPin PDPin PDPin */
+  GPIO_InitStruct.Pin = Frontend_Out_Pin|Loop_Disable_Pin|Loop_Enable_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : PtPin */
+  GPIO_InitStruct.Pin = Loop_Status_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;
+  GPIO_InitStruct.Pull = GPIO_PULLUP;
+  HAL_GPIO_Init(Loop_Status_GPIO_Port, &GPIO_InitStruct);
+
+  /* EXTI interrupt init*/
+  HAL_NVIC_SetPriority(EXTI3_IRQn, 0, 0);
+  HAL_NVIC_EnableIRQ(EXTI3_IRQn);
+
+}
+
+/* USER CODE BEGIN 2 */
+
+/* USER CODE END 2 */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/