changes, enable ethernet

cube/cube.ioc

@@ -21,13 +21,13 @@ Mcu.Pin12=PB15
 Mcu.Pin13=PA8
 Mcu.Pin14=PA9
 Mcu.Pin15=PA10
-Mcu.Pin16=PA13
-Mcu.Pin17=PA14
-Mcu.Pin18=PB5
-Mcu.Pin19=PB6
+Mcu.Pin16=PA12
+Mcu.Pin17=PA13
+Mcu.Pin18=PA14
+Mcu.Pin19=PB5
 Mcu.Pin2=PD0-OSC_IN
-Mcu.Pin20=VP_SYS_VS_Systick
-Mcu.Pin21=VP_TIM1_VS_ClockSourceINT
+Mcu.Pin20=PB6
+Mcu.Pin21=VP_SYS_VS_Systick
 Mcu.Pin3=PD1-OSC_OUT
 Mcu.Pin4=PA4
 Mcu.Pin5=PA5
@@ -59,6 +59,9 @@ PA10.GPIOParameters=GPIO_Label
 PA10.GPIO_Label=Debug_RX
 PA10.Mode=Asynchronous
 PA10.Signal=USART1_RX
+PA12.GPIOParameters=GPIO_Label
+PA12.GPIO_Label=MAINS_CNT_CLK
+PA12.Signal=S_TIM1_ETR
 PA13.Mode=Serial_Wire
 PA13.Signal=SYS_JTMS-SWDIO
 PA14.Mode=Serial_Wire
@@ -79,6 +82,8 @@ PA7.GPIOParameters=GPIO_Label
 PA7.GPIO_Label=EEPROM_MOSI
 PA7.Mode=Full_Duplex_Master
 PA7.Signal=SPI1_MOSI
+PA8.GPIOParameters=GPIO_Label
+PA8.GPIO_Label=MAINS_CNT_TRG
 PA8.Signal=S_TIM1_CH1
 PA9.GPIOParameters=GPIO_Label
 PA9.GPIO_Label=Debug_TX
@@ -176,6 +181,8 @@ RCC.USBFreq_Value=72000000
 RCC.VCOOutput2Freq_Value=8000000
 SH.S_TIM1_CH1.0=TIM1_CH1,Input_Capture1_from_TI1
 SH.S_TIM1_CH1.ConfNb=1
+SH.S_TIM1_ETR.0=TIM1_ETR,ClockSourceETR_Mode2
+SH.S_TIM1_ETR.ConfNb=1
 SPI1.BaudRatePrescaler=SPI_BAUDRATEPRESCALER_8
 SPI1.CalculateBaudRate=9.0 MBits/s
 SPI1.Direction=SPI_DIRECTION_2LINES
@@ -190,11 +197,9 @@ SPI2.VirtualType=VM_MASTER
 TIM1.Channel-Input_Capture1_from_TI1=TIM_CHANNEL_1
 TIM1.ClockDivision=TIM_CLOCKDIVISION_DIV1
 TIM1.IPParameters=Channel-Input_Capture1_from_TI1,Prescaler,ClockDivision
-TIM1.Prescaler=71
+TIM1.Prescaler=13
 USART1.IPParameters=VirtualMode
 USART1.VirtualMode=VM_ASYNC
 VP_SYS_VS_Systick.Mode=SysTick
 VP_SYS_VS_Systick.Signal=SYS_VS_Systick
-VP_TIM1_VS_ClockSourceINT.Mode=Internal
-VP_TIM1_VS_ClockSourceINT.Signal=TIM1_VS_ClockSourceINT
 board=custom